Search
Viewed products
The kit consists of two parts. The...
The kit consists of two parts. The first is an articulated tool for placing and installing the HFN-S2 sensor inside and onto the bracing in a petite bouche Selmer. The second is a tool for pulling the endpin jack or endpin jack preamp into place from the sound hole to the end block.
Ideal for Ukes, Guitars and other instruments with small to medium sized soundboards where a small size and the light weight of the pickup are of utmost importance. The LP-15 Insider comes ready to install and is pre-wired to an endpin jack. The LP-15 series is a new and revolutionary design for soundboard pickups. The LP-15 pickups are the smallest,...
The Mini Pre is a compact single channel preamp. It is only 1 inch thick, 2 inches wide, and a touch over 3 inches in length (25mm x 50mm x 80mm). Weight is 4.5 ozs. (125 grams) with a battery. Specifications: - Input - 1/4" Mono - Output - 1/4" Mono - Input Impedance - up to 10 MOhm - Output Impedance - Less than 3.5 kOhm - Battery Life - 9 volt alkaline...
The HFN-S2 is designed to give you a full, rich sound and will reproduce exactly what your gypsy jazz guitar sounds like. Along with being simple to install, these pickups exhibit excellent feedback rejection and good string to string balance. All HFN-S2's are designed to be used with a preamp - for best results, the HFN-S2 passive may be paired up with...
The HFN-C is designed to give you a full, rich sound and will reproduce exactly what your classical guitar sounds like. Along with being simple to install, these pickups exhibit excellent feedback rejection and good string to string balance. All HFN-C's are designed to be used with a preamp - for best results, the HFN-C passive may be paired up with one...
The HFN is designed to give you a full, rich sound and will reproduce exactly what your guitar sounds like. Along with being simple to install, these pickups exhibit excellent feedback rejection and good string to string balance. All HFN's are designed to be used with a preamp - for best results, the HFN passive may be paired up with one of our outboard...
The EP-01 is a small, light weight piezo sensor that is usually installed internally on an instrument's soundboard. The pickup comes with 18" of shielded cable.The EP-01J adds an endpin jack to the basic EP-01. It is not pre-wired to the jack. The piezo element is covered with an acoustic foam pad to help protect the element. Since the element is not...
T-2 thumbwheel controls are small, circuit board mounted units that can be used as a volume and tone control or as two volume controls. T-2's are also designed to easily be split into two single thumbwheel units should you want to use single thumbwheels for any purpose. T-2's use 500k thumbwheels and come complete with 24 inches of 5 conductor shielded...
The BJ-02 series sensor is designed to work on any banjo. Five string, tenor, six string, open backs; all sound excellent with this pickup. Installation of the pickup system takes about ten minutes and everything that you need to complete the installation is included with the system.The pickup comes supplied with 3M VHB tape for mounting the sensor (as...
The EP-01 is a small, light weight piezo sensor that is usually installed internally on an instrument's soundboard. The pickup comes with 18" of shielded cable. The piezo element is covered with an acoustic foam pad to help protect the element. Since the element is not 'potted' or heavily protected from damage, this sensor is normally installed either on...
Ideal for Ukes, Guitars and other instruments with small to medium sized soundboards where a small size and the light weight of the pickup are of utmost importance. The LP-15 Outsider comes ready to use and has a ten foot cord and standard 1/4" plug. The LP-15 series is a new and revolutionary design for soundboard pickups The LP-15 pickups are the...
The M-06 Neo is a continuation of our M-06 Series of mandolin pickups for adjustable bridged instruments - but with an entirely new type of jack assembly. The M-06 Neo allows you add a pickup system to your mandolin without having to change your bridge or make any invasive changes to your instrument and it features our new Neo-Jack assembly that mounts...
The RB-2 (passive) provides our RB bridge sensor, black jack assembly and adds a second sensor that fits to the fingerboard for that Rock-A-Billy string slap. Included with the RB-2 is a pair of integrated thumbwheel volume controls for balancing the pickups. The controls mount to the underside of the fingerboard. Main Sensor: The RB sensor has a nominal...
The RG-03 is the original center mounted resonator guitar pickup for spider bridge instruments. It comes pre-wired to an endpin jack and is ready for installation. The RG-03 is the way to go for faithful sound reproduction, ease of installation, great anti-feedback characteristics, and so much more. The sensor for the RG-03 mounts easily to the center of...
Two large pieces of medium and soft putty for mounting pickups outside or inside most instruments. Used with our HFN series, EP and LP series, Dualie pickups.
Battery bag with self adhesive velcro. Holds a standard 9 volt battery.
The MVC jack assembly gives you a secure and reliable mounting for the output jack. On these thicker bodied instruments using a clamp-on jack assembly is just not practical thing. The MVC jack assembly, which nestles in right next to the tail piece, is only a half an inch high and mounts from the tailpiece (not the body). The BM-1 sensor is small and...